car wont go into gear after clutch install

Always recheck this adjustment after a couple of hundred miles on a new clutch. I starting to believe the clutch itself or the transmission is broken.

10 Things To Keep In Check When Driving A Typical Manual Transmission

The car wont go into gear when the car is ON.

. Heres my issue I cant shift gears when I press down the clutch. It wont even attempt to start. The Reasons for Manual Transmission Wont Go into Gear When Running.

Reach into the car from the drivers door and feel the clutch pedal with your hand. A couple of times I will push in the clutch while. If it isnt bleed it again.

This should allow it to disengage and go into gear once you start the engine. It did not go into any gear while running with the clutch all the way to the floor. But I can start the car in gear and let go of the clutch and it moves forward just fine.

Its almost like the clutch never engages. I made it to my house and now my car wont go into first gear. It would not go into any gear.

The tranny can shift through all the gears when the car is off but started it wont go into a gear but reverse at which point it wont come. I have researched this and it can be due to a worn clutch fork which was worn and repaired. I have taken the car apart again and reinstalled everything again and still no start.

Lets check if your car is having issues in these areas. The worst time I have getting into gear is after the car has set a few days. Put it into gear drove it for about 50 feet in first.

Put it in reverse turned it around drove it back. All the bolts are in and torqued to the correct specs. Look into the clutch.

1 cycle press clutch to floor open bleeder close repeat. Wont go into gear. Its NOT as quick or easy as bleeding brakes.

I shut off the car put it in first and started it with the clutch in. The pedal felt firm. Discussion Starter 1 Mar 9 2016.

Yesterday I installed a Stage 4 XTD Clutch unsprung six puck. Moving the stick forwards and backwards is causing the shift linkage to move back and forth but it doesnt seem to engage the gears at all. It will not go into any gear.

Haha my clutch line is hooked up and yes the slave cylinder is actuating. After we installed the new clutch Mcleod Stage 2 flywheel clutch fork and adjustable clutch cable the foxbody does not want to go into gear and we have already adjusted the cable to its limits. Put it all back together and the shifter goes through all the gears no trouble but when turned on will not go into any gear.

Heres the story now this morning got in the car and wont go in gear even if god tried after trying to let the car warm up it finally goes in with force drove down a block and then the car works perfect. If the car can go into gear without the clutch being depressed the transmission needs to be removed again. I checked my reservoir which holds both brakeclutch fluid and it was on the minimum line.

GuruXJTFJ answered 2 years ago. Car wont go into gear while the engine is running after new clutch install. Now it will not go into gear.

The car will shift fine once you are moving it will go into 1st-5th gears just fine if the car comes to a. I have had the issue temporarily fixed by bleeding the clutch but air is getting back in some how. Once everything was back together I started the car up and tried to put it into gear to no avail.

Although I can shift when the car is off and it moves. Joined May 16 2012. The clutch isnt disengaging it seems.

When put back together still nothing. However changing gears is impossible while car is running. 2 of 2 Go to page.

I can hear my synchros trying soooo hard to work but the car wont shift. How to fix a car that wont go into gear DIY with Scotty Kilmer. 21 - 26 of 26 Posts.

How to bleed the clutch system. Just changed my clutch. After replacing the clutch pressure plate and clutch release bearing my car wont start at all.

After getting towed home I took this video while I was moving the gearshift. When the clutch pedal is fully pressed the car will still want to creep forward if you put it into gear before turning on and wont shift into. Tranmission wont go into gear after clutch install.

Up to 20 cash back The thicker and newer a clutch is the more travel the hydraulic system has to have to operate the clutch and make it disengage to allow it to go into gear. I will back out off the garage and when I go to put into first the clutch pedal is on the floor and I cannot shift into first. Transmission wont go into gear after clutch installed.

When the car is OFF it will shift through each gear smoothlyThe clutch pedal is very soft and will sometimes stick to the floor but it usually just slowly rises back into its resting position. Okay the car will shift when the car is off. The one way of checking it is to.

Instead when I try to shift it doesnt go into gear and I hear a loud gear grinding noise every time. Jump to Latest Follow Hey everyone. Voting is open for Decembers E46 of the Month Challenge.

My car wouldnt want to go into first cause it would grind. I got a used block put new rings pistons valves gaskts seals et then decidd i should go ahead and install a new clutch as well i mounted them together then dropped them both in enginetranny. Im going to bleed the slave clutch cable.

What do I do I dont want to pay another 1300 for a clutch install. This is much more accurate than your foot if you are not used to adjusting a clutch. Postby Razi Mon Apr 25 2011 158 pm.

I installed a new clutch and now when the car is on it wont shift into any gear. New clutch install car wont move now. Adjusted the pedal even put a new slave cylinder on in case it was that.

Also when applying the clutch I can hear a whirring noise from the TO bearing. I called the mechanic and hes saying its my fault cause I bought a used pressure plate. I have no clue as to why i am having this problem.

Jump to Latest Follow 1 - 7 of 7 Posts. I took everything back apart and checked the clutch plate and it is in there correctly. I also went left to right and then up into gearnothing.

The car goes into gear but wont stall or. I have had this trans out 3 times and each time its the same issue. The problem could be the result of a stubborn clutch refusing to disengage.

I just had the same problem after installing my clutchslave assembly. Id have someone take a look at the slave cylinder as you push the clutch pedal to make sure its moving as much as it should. When I shut it off it went into every gear without an issue.

It will not go into reverse. The car will start while in gear and the clutch will engage fine. How to replace clutch master cylinder.

It take 40 or 50 cycles to bleed the slave if the system has been opened to do the install. There are some specific reasons for the manual transmission to behave in that way. When the car was raised front end up still and put together enough to start it no transaxle wheel ect.

If I pull the clutch up with my foot I can then shift but it will be difficult for a bit. It is possible that the throwout bearing was the wrong one but if you carefully compared the two you can eliminate that from the list of possible problems. This is on an 01 Mustang with the baby 38l and a T5OD tranny.

I installed a ACT xtreme duty clutch on my 02 wrx and ever since Ive had it installed it wont go into gear while the engine is running and the car is not moving.

Clutch Failure Common Causes And Replacement Advice Know Your Parts